If you find yourself in possession of a whole house manganese and iron water filter and have a need to replenish the filter’s media, CQ-BR Filter Media offers an effective filtration solution.

In most cases raw water entering the home will contain iron in the +2 ionic state (ferrous) which makes it practically impossible to filter out. CQ-BR Filter Media enhances the oxidation reaction of ferrous iron to ferric iron and produces ferric hydroxide, an easily filtered precipitate.

CQ-BR Filter Media’s physical characteristics make it an excellent filter for removing the precipitate once formed. Simple backwashing of the filter system will then remove the precipitate from the CQ-BR Filter Media bed.

Testing for iron and manganese in water

Iron — To test for total iron in water, meaning both ferrous iron and ferric iron at the same time, most testing systems will require conversion of all ferric iron to the ferrous state first. The Visual Iron Test Kit offered by the makers of SenSafe Test Kits does an excellent job of converting all ferric iron to ferrous iron and then detecting the amount of iron in a water sample. Detection Range: 0.01 ppm to 5.00 ppm

Manganese — One testing option, SenSafe Manganese Check allows users to test for dissolved manganese in water in concentrations between 0.02 ppm and 2.0 ppm in under 3 minutes and eliminates interferences from several common ions such as copper, iron, cobalt, lead, nickel, and others.

When testing for this type of iron, make certain that the test kit you choose can detect this type of iron. Sounds stupid for us to say that, but some iron in water test kits cannot detect ‘red iron’ and thus do not yield true total iron readings in water.

For a true reading of ALL the iron in your water, and not just the dissolved iron, we suggest the WaterWorks Total Iron Visual Test Kit which detects both forms of iron typically found in drinking water: Fe+2 and Fe+3.

In search of a quality water filtration system capable of removing all forms of iron? Check out the fine selection of home and office water filtration systems offered by the folks over at FilterWater.Com.

Most times the reddish rusty color comes from iron in the water and under normal circumstances that iron comes in two forms: Ferrous and Ferric (AKA: Clear and Red, +2 and +3)

In the past testing for ‘total iron’ required more complex testing methods but recently a simple, at-home total iron test hit the market:

Industrial Test Systems, Inc. (ITS), located in Rock Hill, SC, recently announce the release of its new WaterWorks^TM Total Iron visual test which detects ferric (Fe+3) as well as ferrous (Fe+2) forms of iron. They developed this test to make accurate total iron testing easier and possible without the use of a meter. Test times range around 3 minutes or less and require a very simple test procedure. See below:

WaterWorks^TM Total Iron

TEST PROCEDURE:

1. Add contents of one iron powder pillow to the supplied vial.
2. Fill the vial with water sample to top line.
3. Close the vial with the screw cap and shake for 20 seconds.
4. Wait 3 minutes for the color to develop.
5. Remove the cap.
6. Place vial in white circles and look down into the vial to match to the nearest color block, on the reverse side, to determine the iron concentration.

National Secondary Drinking Water Regulations, as set forth by the USEPA, recommend an iron level of no more than 0.3 ppm. Detection levels for the WaterWorks^TM Total Iron visual test are 0, 0.3, 0.5, 1, 3, 5 mg/L (ppm). The test kit contains 50 individually wrapped foil powder pillows, a test vial with cap, and a color chart card — everything you need to detect total iron in drinking water.

Interested in purchasing the WaterWorks^TM Total Iron visual test kit? Click here.

WaterWorks^TM Total Iron

TEST PROCEDURE:

1. Add contents of one iron powder pillow to the supplied vial.
2. Fill the vial with water sample to top line.
3. Close the vial with the screw cap and shake for 20 seconds.
4. Wait 3 minutes for the color to develop.
5. Remove the cap.
6. Place vial in white circles and look down into the vial to match to the nearest color block, on the reverse side, to determine the iron concentration.

National Secondary Drinking Water Regulations, as set forth by the USEPA, recommend an iron level of no more than 0.3 ppm. Detection levels for the WaterWorks^TM Total Iron visual test are 0, 0.3, 0.5, 1, 3, 5 mg/L (ppm). The test kit contains 50 individually wrapped foil powder pillows, a test vial with cap, and a color chart card — everything you need to detect total iron in drinking water.

Interested in purchasing the WaterWorks^TM Total Iron visual test kit? Click here.